|
Three
Phase - 460
& 230/460 Volts - Rigid
Base
1
thru 400 Hp NEMA 143T thru 449T
Applications:
Petro-chemical
plants, mines, foundries, pulp and paper plants, waste management facilities, chemical plants,
tropical climates and other processing industry applications requiring corrosion
protection from severe environmental operating conditions.
Features:
1.15
Service Factor, corrosion resistant epoxy finish, regreasable ball or roller bearings, oversized rotatable
cast iron conduit box, cast iron frames, Forsheda®
shaft
seal, moisture resistant copper windings, Class F insulation, tropicalization, stainless steel
nameplate and corrosion resistant hardware. ECP Super-E motors have NEMA Premium™
efficiency and 3 year warranty.
Three
Phase - Super-E® - 575
Volts, Rigid Base
1
thru 200 Hp NEMA 143T thru 445T
Applications:
Petro-chemical plants, mines, foundries, pulp and paper plants,
waste management facilities, chemical plants, tropical climates and other
processing industry applications requiring protection against corrosion caused
by severe environmental operating conditions.
Features:
1.15 S. F. Corrosion resistant epoxy finish. Regreasable ball bearings.
Oversized rotatable cast iron conduit box. Forsheda® shaft seal. Moisture
resistant ISR® copper windings. Class F insulation. Stainless steel nameplate
and corrosion resistant hardware. Tropicalized. NEMA Premium™ efficiency
and 3 Year Warranty.
Three
Phase -
460
Volts - C-Face
1
thru 25 Hp NEMA 56C thru 215TC
Applications:
Petro-chemical plants, mines, foundries, pulp and paper
plants,
waste management facilities, chemical plants, tropical climates and other
processing industry applications requiring corrosion protection from severe
environmental operating conditions.
Features:
1.15 Service Factor, corrosion resistant epoxy finish, regreasable
ball
bearings, oversized rotatable cast iron conduit box, cast iron frames, Forsheda
shaft seal, moisture resistant copper windings, Class F insulation, tropicalization,
stainless steel nameplate and corrosion resistant hardware. VECP
Super-E motors have NEMA Premium™ efficiency and 3 year warranty.
Three
Phase - IEEE 841- 460
Volts, Rigid Base and
C-Face
1
thru 250 Hp NEMA 143T thru 449T
Applications:
Petro-chemical, pulp and paper plants, mines and other installations
requiring premium efficient motors manufactured and tested to rigid
standards for severe duty service.
Features:
Exceeds IEEE 841-2001 standards for severe duty TEFC induction motors.
Premium efficiency copper windings using Baldor ISR® (Inverter Spike Resistant®)
magnet wire. Inpro/Seal® VBX bearing isolator on fan and drive end shaft
extensions, 2-part epoxy primer (inside & outside), gray epoxy paint
and corrosion resistant hardware.
Reduced noise, vibration and mechanical tolerances;
final test and vibration results shipped with motor. Complies with NEMA
Premium™ efficiency guidelines. 5 year warranty.
Three
Phase - IEEE841 - 575
Volts, Rigid Base
1
thru 250 Hp NEMA 143T thru 449T
Applications:
Petro-chemical, pulp and paper plants, mines and other installations
requiring premium efficient motors manufactured and tested to rigid
standards for severe duty service.
Features:
Exceeds IEEE 841-2001 standards for severe duty TEFC induction motors.
Premium efficiency copper windings using Baldor ISR® (Inverter Spike Resistant®)
magnet wire. Inpro Seal® on fan and drive end shaft extensions, 2- part
yellow epoxy oxide primer (inside & outside), gray epoxy paint and corrosion
resistant hardware. Reduced noise, vibration and mechanical tolerances;
final test and vibration results shipped with motor. Complies with NEMA
Premium™ efficiency guidelines. 5 year warranty.
Three
Phase - Medium Voltage
- 2300/4160 Volts,
Rigid Base
200
thru 500 Hp NEMA 449TS thru 5011L
Applications:
Petro-chemical plants, mines, foundries, pulp and paper plants,
waste management facilities, chemical plants, tropical climates and other
processing industry applications requiring corrosion protection from severe
conditions.
Features:
Form coil VPI construction, copper bar rotor(1), all cast iron, NEMA
Premium™ efficiency three year warranty.
Three
Phase - Quarry Duty
Motors - TEFC, Design
C, High Torque
1
thru 15 Hp NEMA 56C thru 254T
Applications:
Conveyors, gear reducers and applications requiring
Design
C torques.
Features:
Cast iron frame, Class F insulation, Class B rise. UL and CSA recognized
component approval.
Three
Phase - Crusher Motors
-TEFC, 460 Volt, Rigid
Base
100
thru 300 Hp NEMA 405T thru 449T
Applications:
Belt-driven rock crushers, pellet mills, and other applications requiring
motors rated for severe duty service and high starting torques.
Features:
High torque design exceeds NEMA Design C locked rotor, pull up,
and
breakdown torques. 1.15 Service Factor. Corrosion resistant epoxy finish. Regreasable
bearings. Oversize, rotatable cast iron conduit box. Forsheda® shaft
seal. Moisture resistant copper windings with Class F tropicalized insulation.
Stainless steel nameplate and corrosion resistant hardware. Pulley end
roller bearings and high strength steel shaft for belted loads only; not suitable
for direct coupled loads.
Three
Phase - Dirty Duty
1/2
thru 20 Hp NEMA 56 thru 256T
Applications:
Petro-chemical plants, mines, foundries, pulp and paper plants,
waste management facilities, chemical plants, tropical climates and other
processing industry applications requiring corrosion protection from severe
conditions.
Features:
1.0 Service Factor at 50°C ambient, weatherproof per IEEE 45
and
USCG 259 marine duty (below deck duty only). 416 stainless steel shaft for
corrosion protection from severe conditions.
|
